LAB-2 (Tutorial) Simulation of LNA (Cadence SpectreRF) - PDF LAB-2 (Tutorial) Simulation of LNA (Cadence SpectreRF) - PDF

{REGREPLACE2-#,$#-#.#}Spectrerf simulation dating, {dialog-heading}{/REGREPLACE2}

Perturbation Based Measurements appNote and database: You can use the fixed Q inductor from cadence menu and remove this resistor. Capacitor can be added in parallel with the Ld to make the gain and NF response more selective and narrow.

SpectreRf Cadence

This is available in IC5. Example circuits where you might use the Periodic small-signal analyses include conversion gain in mixers, noise in oscillators, and switched-capacitor filters. Input and Output Impedance Spectrerf simulation dating 5.

In case of differential LNA the even mode disturbances will be suppressed.

Oscillator Noise Analysis in SpectreRF

There are many views available when you place the symbol in schematic, use Symbol or Specrtre view only. The Signal Partitioning workshop describes how to speed up SpectreRF harmonic balance simulation by using signal partitioning for special circuit designs. These instruction will guide you how to list, load and remove the modules Create a new directory myrfdir where your simulation data will be stored.

What is minimum condition of stability for LNA? You can also measure the Z-parameters like Z11 and Z Usually there is more than one method available to simulate the desired parameter; we will use the procedure recommended by cadence and takes less simulation time.

That is, S11 is close to zero. In this case, you should use transient analysis to simulate the circuit. Proceedings of the 32nd Design Automation Conference, June NF, Input and Output Noise using Pnoise Analysis The Pnoise analysis summary shows you the contributions of different noise sources in the total noise.

This is very powerful feature to focus the effort spectrerf simulation dating improve the noise performance of the device which contributes the maximum noise.

The conventional smallsignal analyses AC, SP, XF, and Noise linearize about the DC or time-invariant operating point and age gap couples celebrity dating do not include frequency conversion effects.

After the PSS analysis, we can observe the harmonic distortion of the LNA by plotting the spectrum of any node voltage. Therefore, the gain from PSS should match GP spectrerf simulation dating the input power level is low and nonlinearity is weak. To character the LNA following figure of merits are usually measured.

Efficiency of the simulation drops when the Tis long compared to the periods of the stimuli. Which S-parameter directly characterizes the reverse isolation gain? Once the simulator has performed a PSS analysis, it can linearize the circuit about a periodic time varying operating point and can include frequency conversion effects.

Z RF Measurement Library: IP3 plot above is not very nice looking, one can do more iterations and come up with better aligned 3 rd order line with 3 rd order plotted data. Cadence Setup Guidelines 1.

We will be using AMS 0. It also allows you to customize analyses and outputs to a greater extent than is currently possible in ADE. If the specific source is power supply node then we can measure the PSRR.

SpectreRF pioneered a variety of periodic small-signal analyses, including periodic AC pacperiodic noise pnoiseperiodic transfer function pxfperiodic s-parameter psp and periodic stability pstb. Therefore, you should use the PSS and Pnoise analyses.

How to use SpectreRF simulates Zin/Zout?

Voltage Gain and Harmonic Distortion Fig9: Eventually the dominance of SpectreRF faded as the use of Krylov subspace methods propagated to other simulators, particularly those based on harmonic balance. The components values are listed below for your convenience. The more nonlinear the relationship between initial and final points, the greater number of iterations needed by the PSS analysis, which causes the PSS analysis to take longer.

This might help in the input and output impedance matching circuit design.

LAB-2 (Tutorial) Simulation of LNA (Cadence SpectreRF)

Power Consumption and Supply Voltage 2. As the input power level increases, the circuit becomes nonlinear, the harmonics are generated and the noise spectrum is folded. If Balun is used in your testbench, you may find this in the Library rflib. SpectreRF now provides harmonic balance in addition to shooting methods, both of which are accelerated using Krylov subspace methods.

How we can relate the S-Parameters to the gain, input impedance and output impedance of any two-port network?

How to use SpectreRF simulates Zin/Zout?

These simulators were based on harmonic balance and could reliably simulate circuits with tens of transistors whereas SpectreRF could simulate circuits with thousands of transistors.

Long Term Jitter Measurements appNote: The Stern stability factor K and can be plotted in two ways. You must answer the questions in the LAB compendium before you start the tutorial, this will help you to effectively comprehend the tutorial material and simulations methodology.

The results are shown in Fig Well, the more things change This gain definition is the same as that for GP. If the circuit is driven with more than one periodic stimulus, then the frequencies must all be commensurate or co-periodic, and Tmust be the common period or some integer multiple of it.

Re: How to use SpectreRF simulates Zin/Zout?

Please read the complete manual before you start the software. PSS quickly computes the steady-state response of circuits that exhibit extremely long time constants, such as high-Q filters and oscillators.

The measurement aware approach allows you to place multiple measurements on a schematic. After performing a PSS analysis, you can perform one or more of the periodic small-signal analyses.

Oscillator Noise Analysis in SpectreRF

The stability curves for K and as plotted with respect to frequency sweep as shown in Fig-6 or they can be plotted as load stability circle LSB and source stability circle SSB.

S11 or input matching can be improved by changing the source degeneration inductor Ls 10 Spring This is significant as periodically time-varying linear models, unlike the time-invariant linear models used by the traditional small-signal analyses AC and noise exhibit frequency conversion.

Signal partitioning provides a method of decomposing a circuit so that multi-rate behavior can be exploited to increase simulation performance. It adds a series of analyses that are particularly useful for RF circuits to the basic capabilities of Spectre. Pdisto analysis computes the steady-state responses of a circuit driven by two or more signals at unrelated frequencies.